ISO 5349-2 PDF

The ISO Central Secretariat accepts no liability in this area. International Standard ISO was prepared by the European Committee for. Buy KS B ISO Mechanical vibration — Measurement and evaluation of human exposure to hand-transmitted vibration — Part 2: Practical guidance. ISO MECHANICAL VIBRATION – MEASUREMENT AND EVALUATION OF HUMAN EXPOSURE TO HAND-TRANSMITTED VIBRATION – PART 2.

Author: Yojinn Misar
Country: Saint Lucia
Language: English (Spanish)
Genre: Love
Published (Last): 13 December 2011
Pages: 350
PDF File Size: 19.35 Mb
ePub File Size: 8.93 Mb
ISBN: 282-5-59512-661-4
Downloads: 40201
Price: Free* [*Free Regsitration Required]
Uploader: Tajind

Take the smart route to manage medical device compliance. The experimenter should determine the main sources e. This does not preclude the free use, in course of implementing the standard, of necessary details, such as symbols and sizes, type or grade designations. Hand-held mounting systems rely in the operator’s grip force to hold the mounting system in place; although, it often is advisable to lightly hold the adaptor in position on the vibrating surface using elastic adhesive tape.

NOTE In practice, the sensitivity of accelerometers rarely drifts during measurements, however, they may suffer mechanical failure.

InterRegs: EN ISO : | Mobile Construction Equipment

53499-2 However, in the case of small rotary angle sanders and polishers, where the motor housing is intended to be held, the housing shall be treated as a handle. Practical applications of the calculation iiso the daily vibration exposure are given In annex E.

For each operation, at least three samples should be taken. Often a typical daily vibration exposure time will be based on – a measurement of the actual exposure time during a period of normal use e.

In addition uncertainty of the overall evaluation of vibration exposure will be affected by changes which occur in the course of any working day, such as – changes in the condition of power tool and ido tool e. Care should be taken to ensure that any resonance frequencies of the mounting assembly are high enough above the upper limit of the measurement frequency range.

A method shall be chosen which gives an adequate fixing to the vibrating surface, does not interfere with the isoo of the power tool and does not itself affect the vibration charadteristics of the vibrating surface.

  BARBER NUVOLETTA PDF

Key Terminology Vibration Emissions—The vibration produced by kso and tools and often relating to the quality of the ieo Vibration Exposure—The effect of machine and tool vibration on the user; the impact on the operator using the tool.

This Indian Standard has been developed from Doc: The second part of the day is spent using a chain saw, where trees are first felled and then the trunks are stripped of branches; 30 trees are felled and stripped per day.

Saws, polishing and filing machines with isso action and small saws with oscillating or rotating action. For impactive tools, where the impact rate impacts per second is less than 10 times the frequency increment of the narrow-band analysis, then other window functions should be considered.

BS EN ISO 5349-2:2001+A1:2015

Vibration am Arbeitsplatz; Grundlagen, Messerfahrungen und praktische Hinweise fur den Arbeitsschutz. In general, the European and other vibration directives are designed to help employers reduce risk of employee injury and liability.

For many hand-held power tools, specific measurement locations and axes have been defined for isk measurement of vibration emission by ISO and other International Standards: Limits for maximum exposure which are called the T h r e s hol d Li m i t V alue T L V and action levels are shown below.

Mesurage et evaluation de l’exposition des individus aux vibrations transmises par la main. Identifying workplaces with vibration exposure Establishing realistic typical exposure time—For example, an employee that operates high vibration equipment may only do so for a few minutes even though they use that tool during their entire shift—e.

Less than 1 hour. The results of these verification checks shall be recorded. Unfortunately, continuous exposure to mechanical vibration can lead to serious injury.

The effect on the human body is dependent upon the magnitude of vibration, the frequency content, and the duration of exposure. In such situations Isl requires that an appropriate multiplication factor is applied to a single- or two-axis measurement result to give an estimated vibration total value.

An Introduction to Hand/Arm Vibration

In general, care should be taken izo ensure that any cable connections are secure and that the cables have not been damaged in any way. Minimum performance requirements e.

  BARRY GREEN DVX BOOK PDF

Review of Indian Standards Amendments are issued to standards as the need arises on the basis of comments. Metal or nylon straps have been successfully used.

Practical guidelines for measuring human exposure to hand-transmitted vibration at the workplace.

An Introduction to Hand/Arm Vibration – National Instruments

The vibration exposure may vary greatly from one operation to another, either due to the use of different power tools or machines or different modes of operation of one power tool or machine. Some analogue and some digital recording systems use data compression techniques to minimize the space taken by the data; these techniques should be avoided, unless it can be shown that such systems do not lose signal information.

Where very short duration measurements are unavoidable e. Information on the fundamental resonance frequency will be available from the accelerometer manufacturer.

Measurements of vibration magnitude can only be made over the time taken to fix five wheel nuts. For very low impact rates, e.

Copyright BIS has the copyright of all its publications. Users of Indian Standards should ascertain that they are in possession of the latest amendments or edition by referring to the latest issue ixo ‘BIS Catalogue’ and ‘Standards: For each operation i, the vibration total value, afhvi.

It is important that digital methods, such as digital filtering and Fast Fourier Transform FFT analysis, are properly capable of providing accurate analysis over the full frequency range covered by the one-third-octave bands from 5439-2 Hz to Hz.

Wrenches, nut runners and screwdrivers. For piezoelectric accelerometers, the fundamental resonance frequency should normally be much higher, ideally greater than 30 kHz, to minimize the likelihood of DC-shift distortion see 6.

Where vibration 549-2 is evaluated over periods greater than one day, the results shall not be used to determine risks to health. This may have to be a simulation of uninterrupted work e.