Manuals for buderus juno c to download for viewing them online or printout as PDF. Manuals for Buderus Juno 11 download to download for viewing them online or printout as PDF. Buderus Manuals for Support Juno /SF Buderus | GB | Operating instructions | Buderus GB Operating instructions . .. 46 Shut down the heating system using the control unit.
|Published (Last):||26 December 2010|
|PDF File Size:||10.98 Mb|
|ePub File Size:||14.61 Mb|
|Price:||Free* [*Free Regsitration Required]|
Y Pump feedback fault. All Boilers are supplied with a manual reset limit thermostat. The return port is plugged and the Bypass Screw is not fitted.
Download – Buderus –
After the set time has expired, the heating system returns to automatic heating mode. Never use chlorine and hydrocarbon containing chemicals such as spray chemicals, solution and cleaning agents, paints, glues etc in the vicinity of the boiler.
It changes over between day mode standard mode and night mode setback mode. The newly selected DHW temperature is saved in approximately 2 seconds.
Only operate the DHW circulation pump via a time switch.
Operating instructions Logamatic |
Fit an approved terminal guard if in accessible position. With the jkno open, also press “Day mode” or “Night mode”. The relief valve must comply with following specifications: The Logamatic control unit is designed to control heating systems in detached houses, apartment buildings, residential complexes and other buildings. Heating only recommences if the heating system is subject to a risk of frost.
Release “Prog” key to enable the selected standard program here: Subject to the modules, various of the following operating displays can be called up: On no account should any part of the Boiler or ts Flue be modified except as specified in this i manual. Keep Cravat as low as possible onto flashing plate to prevent entry of animals, birds or insects. Textplatte Logamax Plus GB Inspect flue and air ducts for deterioration of seals, and repair if necessary.
In case of faults, immediately notify your heating contractor who will guarantee a professional service. Skin rashes oil Acne. The plate shall be of sufficient size to be easily read from a distance of eight feet away, and read “Gas Vent Directly Below”. Fault message “Time switch not possible” Fault messages. Controlling the extended functions. Troubleshooting 11 11 Troubleshooting Have your heating contractor remedy any faults immediately.
Adhere to national code requirements. Set the required room temperature by turning the rotary selector.
Download – Buderus
Loosen the screw plug on the inlet gas pressure testing nipple by two turns fig. Move the boiler away from the wall and using a diamond tipped core drill, drill a 6 mm hole in the wall ensuring the hole is level. The Flue is telescopic and no cutting of the flue pipes is necessary. Tundish not supplied Provides a visual indication of water flowing from the Pressure Relief Valve.
Check the burner, the heat exchanger and the condensate trap for pollution.
Press “Day mode” if you want to heat at short notice in summer mode. The high level elbow must be slightly sloped downwards. The following example shows how the switching points of the standard program “Family” can be changed for the days Monday to Thursday.
Press the reset button once the temperature has dropped sufficiently. Is the oil line connected to the correct inlet connection of the pump? Improper installation, adjustment, alteration, service or maintenance can cause injury, loss of life or property damage. The important thing is that the various components match each other. Flush system thoroughly and refill.
Pure room temperature-dependent control has, in such cases, certain limitations. Inspect and clean if necessary.
Operating instructions Logamatic 4211
CO2, oil pressure, nozzle size see Technical Data Check all Baffles are in place and correctly located. Positions should be avoided where the exhaust of combustion products could cause nuisance. Check lockout function, either cover the photocell or remove solenoid coil, to simulate flame failure.
If this is the case: It is equipped with an ignition device which automatically lights the burner. This saves you energy. Due consideration to the siting of Boilers should be given. U Supply sensor affected by short circuit.