Reference Manual. INTRODUCTION Thank you for purchasing the Alesis ADAT- XT Digital Multitrack Tape Recorder. To take full advantage of the XT’s functions, . User manual for the device Alesis ADAT-XT. Online user manual database. musical instrument, dj equipment manuals, user guides, spec sheets. Alesis ADAT-XT Recording Equipment User Manual. Page 1. Page 2. Page 3. Page 4.

Author: Yozshutaxe Zubei
Country: Poland
Language: English (Spanish)
Genre: Music
Published (Last): 27 May 2018
Pages: 455
PDF File Size: 20.32 Mb
ePub File Size: 2.47 Mb
ISBN: 767-3-84186-763-2
Downloads: 62515
Price: Free* [*Free Regsitration Required]
Uploader: Shakalrajas

If you are already familiar with multitrack recording concepts, you may not need to read this chapter. This is useful when you want to precisely punch in to a specific place on one or more tracks.

The error is caused by the unit losing sync. If looking through the Alesis ADAT-XT user manual directly on this website is not convenient for you, there kanual two possible solutions:.


Page 19 Chapter manjal During power-up, the XT checks the footswitch to determine whether it isnormally open or normally closed type, and calibrates itself accordingly.

Digital signals for the same 20 kHz audio requires a frequency response of several million Hertz. Eight18 bit linear audio, times oversampling, singl. Locate Points 2 and 3 determine the in and out points. To play back a recording: Page 48 Chapter 4: Alesis will pay for standard one-way shipping back to you on any repair covered under the terms of this warranty. Dimensions H x W x D: Whenturning the XT on or off, be sure to keep monitor levels low.

If only one tape is found to cause this problem, don’t use it. Page 85 The edges of the tape have become damaged. Page 67 XT would cause some phase cancellation when combined with the original signal. Then, by offsetting the original machine the track s manuzl from, you couldbounce back the vocals at the positions corresponding to the other choruses.


Locate Points 2 and 3 determine the in and out points. Contact Alesis for service. Bouncing means taking audio from one track and placing it on another. Crossfading always begins at the punch point and continues for the amount of time you have specified.

Device A One path goes from device A to ground via the ground terminal of the three- conductor AC power cord, but A also sees a path to ground through the shielded cable and AC ground of device B. The processinvolves formatting a tape see previous tutorialputting one or more tracks intorecord-ready, adjusting record levels on your mixer, setting the input monitor mode,locating to the start tape address and engaging record.

Page 86 Appendix D: The longer crossfade time allows for asmoother transition and is more useful when punching in new material that is verydifferent from what is already on tape, or when punching in low-frequency signals.

The transport mnual back and forth for about 5 minutes.


Next, select the source tracks, select record enable the destination tracks, and initiate recording. Page 56 Chapter 4: Manuaal of Contents Add to my manuals Add.

So glad to have found this great resource!

Page 21 Chapter 2: This means you adaf set a Locate at one point, another Locate at another position, then have one of the slave ADATs offset by the amount of time between those two Locate positions. Page 79 Appendix B: When recording, pressing [STOP] will exit record mode and stop the transport.

What’s missing? Tell us about it.

Write this number down or memorize it. Page 82 Appendix B: Auto recording stops and starts recording automatically at predetermined times. This is useful when you want toprecisely punch in to a specific place on one or more tracks. Get familiar with them by using them while watching the TIME counter.


The result is a perfect digitalduplication of the original. Eight tracks allow for recording audience sounds, ambience, and individual soloistsas well as a stereo mix of the PA. Track Copy RACK It is possible to copy the audio material from one track to another on the same tape within the XT without leaving the digital ,anual and without the need for any audio cables. When in Edit Mode, this icon indicates that you are editing a tracks delay amount, which will appear in the TIME counter.

Alesis ADAT-XT user manual – – Solve your problem

The backup can eitherbe sample qdat to the time reference or not. Larger Key Notch Note: The digital representation of the data as stored on tape was therefore inverted relative to the analog input i. Chapter 4the last valid time-stamp it reads from tape. Page 77 Digital Recording Concepts: To bounce audio from one track to another: Page 83 Appendix B: A number from aadat to 8 will appear next to the EDIT icon to indicate which track is being edited.

The option to print the manual has also been provided, and you can use it by clicking the link above – Print the manual. Alesis Sync Cables are available in three different lengths: Check that the power cableis plugged in properly. The currently selected input mode is indicated in the lower right corner of the display: Page 76 Chapter 6: